
HS2800 High Output Blown Air Heater Gas Marine
$1,540.00
The HS2800 is a 2.8kw automatic thermostatically controlled blown air heating system fuelled by Propane or Butane gas. Heatsource is designed for a variety of automotive and marine applications as a source of heat totally independent of the engine.
Product Includes:
Mounting Equipment:
Stainless Marine Mount Bracket
Electrical Equipment:
Propex Wiring Harness
Propex Thermostat
Exhaust & Intake Equipment:
1” S/S Flexible Exhaust Tube 3’ (2)items
1” Galvanized Exhaust Clamp (2) items
Insulation Sock 3’
1 ½” S/S Hose Clamp (2)items
S/S Thru Hull Fitting
Ducting Equipment:
3” PAK Hot Air Duct 20’
Propex 80mm True Wye
Propex 80mmx3” Adapter (5)items
Propex 80mm Non Closable Vent (2) items
75mm Aurora Grill
3” S/S Hose Clamp (8) items
Mounting Equipment:
Vehicle Mount Kit
Electrical Equipment:
Propex Wiring harness
Propex Thermostat
Exhaust and Intake Equipment:
22mm S/S Flexible Exhaust Tube 3’
22mm – 24mm S/S Exhaust Clamp (2) items
Ducting Equipment:
60mm Pak Hot Air Duct 3’
Propex 80mm Non Closable Vents (2) items
S/S Hose Clamp (8) items
Mounting Equipment
Vehicle Mount Kit
Electrical Equipment:
Propex Wiring Harness
Propex Thermostat
Exhaust & Intake Equipment:
22mm S/S Flexible Exhaust Tube (3) items
22mm – 24mm S/S Exhaust Clamp (2) items
Ducting Equipment:
60mm Pak Hot Air Duct 20’
Propex 80mm Non Closable Vent
Propex 75mm Aurora Vent
S/S Hose Clamp (8) items
Mounting Equipment
Vehicle Mount Kit
Electrical Equipment;
Propex Wiring Harness
Propex Thermostat
Exhaust & Intake Equipment:
Hitech 1 Hose 3’
1” S/S Flexible Exhaust Tube 3’
1” Galvanized Exhaust Clamp (2) items
Insulation Sock 3’
1 ½” S/S Hose Clamp (2) items
Ducting Equipment:
Propex 80mm Non Closable Vents (2) items
Mounting Equipment:
Stainless Marine Mount Kit
Electrical Equipment:
Propex Wire Harness
Propex Thermostat
Exhaust & Intake Equipment:
22mm Flexible Exhaust Tube 3’ (2) items
22mm Exhaust Clamp (2) items
Insulation Sock 3’
S/S Thru Hull Filling
1 ½” Hose Clamp (2) items
Ducting Equipment:
20’ 60mm Air Ducting
Propex 80MM True Wye
80mmx60mm Adapter (6) items
Non – Closable Vents (2) items
Closable Vent (1) items
Hose Clamp (8) items
Technical Specifications
Economy | ||
---|---|---|
Average consumption 225 grams/hour |
3.9kg propane cylinder 17.5 hours |
4.5kg butane 20.0 hours |
13kg propane 58.0 hours |
15kg butane 67.0 hours |
19kg butane 84.5 hours |
47kg butane 209.0 hours |
904 Camping gaz (1.81kg) 8.0 hours |
907 Camping gaz (2.72kg) 12.0 hours |
Technical Specifications | ||
---|---|---|
Heat Input: 3.0kW |
Heat Output: 2.8kW |
Voltage: 12V or 24V versions |
Current Consumption: 1.9A continuous running |
Air Throughput: 85 C.F.M. |
Fuel: Butane or Propane Gas |
Economy | ||
---|---|---|
Average consumption 142 grams/hour |
3.9kg propane cylinder 27.5 hours |
4.5kg butane 31.7 hours |
13kg propane 91.5 hours |
15kg butane 105.6 hours |
19kg butane 133.8 hours |
47kg butane 331.0 hours |
904 Camping gaz (1.81kg) 12.75 hours |
907 Camping gaz (2.72kg) 19.0 hours |
Technical Specifications | ||
---|---|---|
Heat Input: 2.1kW |
Heat Output: 1.9kW |
Voltage: 12V or 24V versions |
Current Consumption: 1.4A continuous running |
Air Throughput: 60 C.F.M. |
Fuel: Butane or Propane Gas |
HS2211 Technical Specifications | ||
---|---|---|
Maximum Dimensions Height: 230mm, Width: 157mm, length: 430mm |
Weight Under-floor installation 7.7kg |
Gas Butane 28-30mbar – CAT I3+ (28-30/37), Butane/Propane 30mbar – CAT I3B/P (30) |
Propane 37mbar – CAT I3p (37) |
Gas Consumption (M) 150g/h |
Classification of Heater Type: C53 (Fanned) Normal Installation C13 Vehicle In Motion Installation |
Nominal Heat Input Gas 2.0Kw |
Battery Supply | Nominal Voltage 12V d.c. |
Operating range 10.0V d.c. min. to 15V d.c. max. |
Maximum current d.c. gas operation: 1.7 Amps (0.01Amps on standby) |
Dry Storage Temperature -20°C to 70°C |
Hot Air Duct Diameter 60mm ID |
Flue Diameter 22mm ID |
Maximum Exhaust Flue Length 2m |
Minimum Exhaust Flue Length 0.75m |
Maximum Combustion Air Flue Length 2m |
Minimum Combustion Air Flue Length 1.0m |
Economy | ||
---|---|---|
Average consumption 225 grams/hour |
3.9kg propane cylinder 17.5 hours |
4.5kg butane 20.0 hours |
13kg propane 58.0 hours |
15kg butane 67.0 hours |
19kg butane 84.5 hours |
47kg butane 209.0 hours |
904 Camping gaz (1.81kg) 8.0 hours |
907 Camping gaz (2.72kg) 12.0 hours |
Technical Specifications | ||
---|---|---|
Heat Input: 3.0kW |
Heat Output: 2.8kW |
Voltage: 12V or 24V versions |
Current Consumption: 1.9A continuous running |
Air Throughput: 85 C.F.M. |
Fuel: Butane or Propane Gas |
Dimensions Gas Supply | ||
---|---|---|
Malaga E Only | ||
Overall H 250mm W 325mm D 445mm |
Weight Empty 9.3kg |
Tank Capacity 13 litres |
Water Temperature Thermostat Setting 70 °C |
Overheat Thermostat Setting 90 °C |
Water Supply The heater will operate satisfactorily on either a system where the pump is controlled by the tap microswitches or the one controlled by a pressure switch. It must not be connect to mains water supply. Water connections can be provided to suit a range of standard fittings. Reinforced or semi rigid pipe must be used. |
Pressure Relief Valve Settings 3 bar |
Maximum Working Pressure 2 bar |
Maximum Working Supply Pressure 1.9 bar |
Heat Input 1.15kW 84g/h |
Pressure Settings: Propane 37mbar |
|
Butane 28mbar |
Mixtures 30mbar |
Injector Bray 960/40 |
Electrical Supply 12v DC |
Gas Connection 8mm O.D. |
Mains Electricity Supply 200/240vAC 50Hz Fused 5A |
Economy | ||
---|---|---|
Average consumption 142 grams/hour |
3.9kg propane cylinder 27.5 hours |
4.5kg butane 31.7 hours |
13kg propane 91.5 hours |
15kg butane 105.6 hours |
19kg butane 133.8 hours |
47kg butane 331.9 hours |
904 Camping gaz (1.81kg) 12.75 hours |
907 Camping gaz (2.72kg) 19.0 hours |
Technical Specifications | ||
---|---|---|
Heat Input: 2.1kW |
Heat Output: 1.9kW |
Voltage: 12V or 24V versions |
Current Consumption: 1.4A continuous running |
Air Throughput: 60 C.F.M. |
Fuel: Butane or Propane Gas |
FAQ
Q: I have an old Carver P4 air heater do you do a replacement?
A: Yes, the HS2000, HS2211or the HS2800.
Q: Can the heater be mounted vertically?
A: The heater must not be mounted vertically on its nose or end or upside down but on one of its sides is not a problem. Remember when mounting the unit you should ensure you can still maintain access to the electronics cover and gas connections
Q: Where can the heater be fitted?
A: Most installations are mounted in a bedbox or locker. External installation is not recommended unless using the appropriate mounting box. However the HS2211 is designed to be fitted externally.
Q: How noisy is the heater?
A: There is very little burner noise from the heater itself. However, there will be some noise from the blown hot air similar to that of a small domestic fan heater.
Q: Can the heaters be used while vehicles are moving?
A: Yes, a vehicle in motion flue terminal is available and the heater should be installed and operated in compliance with the relevant regulatory requirements. Use of the the correct VIM bracket ensure compliance with the vehicle in motion test regime.
Q: What length of exhaust flue pipe can be fitted?
A: Total combined length must not exceed 4 meters and the inlet pipe should be slightly longer than the exhaust to balance the burner.
Q: What is the electrical consumption?
A: 1.6amps on 12v
Q: I have an old Carver P4 air heater do you do a replacement?
A: Yes, the HS2000, HS2211 or the HS2800.
Q: Can the heater be mounted vertically?
A: The heater must not be mounted vertically on its nose or end or upside down but on one of its sides is not a problem. Remember when mounting the unit you should ensure you can still maintain access to the electronics cover and gas connections
Q: Where can the heater be fitted?
A: Most installations are mounted in a bedbox or locker. External installation is not recommended unless using the appropriate mounting box. However the HS2211 is designed to be fitted externally.
Q: How noisy is the heater?
A: There is very little burner noise from the heater itself. However, there will be some noise from the blown hot air similar to that of a small domestic fan heater.
Q: Can the heaters be used while vehicles are moving?
A: Yes, a vehicle in motion flue terminal is available and the heater should be installed and operated in compliance with the relevant regulatory requirements. Use of the the correct VIM bracket ensure compliance with the vehicle in motion test regime.
Q: What length of exhaust flue pipe can be fitted?
A: Total combined length must not exceed 4 meters and the inlet pipe should be slightly longer than the exhaust to balance the burner.
Q: How many outlets can you put on the Heatsource HS2000, HS2000E and HS2211?
A: The maximum recommended is 3, providing the total combined length of ducting is no longer than 5 metres and the maximum length to the first outlet should not exceed 1.5m.
Q: What is the electrical consumption?
A: 1.6amps on 12v
Q: Can the heater be mounted vertically?
A: The heater must not be mounted vertically on its nose or end or upside down but on one of its sides is not a problem. Remember when mounting the unit you should ensure you can still maintain access to the electronics cover and gas connections
Q: Where can the heater be fitted?
A: Most installations are mounted in a bedbox or locker. External installation is not recommended unless using the appropriate mounting box. However the HS2211 is designed to be fitted externally.
Q: How noisy is the heater?
A: There is very little burner noise from the heater itself. However, there will be some noise from the blown hot air similar to that of a small domestic fan heater.
Q: Can the heaters be used while vehicles are moving?
A: Yes, a vehicle in motion flue terminal is available and the heater should be installed and operated in compliance with the relevant regulatory requirements. Use of the the correct VIM bracket ensure compliance with the vehicle in motion test regime.
Q: What length of exhaust flue pipe can be fitted?
A: Total combined length must not exceed 4 meters and the inlet pipe should be slightly longer than the exhaust to balance the burner.
Q: How many outlets can you put on the Heatsource HS2000, HS2000E and HS2211?
A: The maximum recommended is 3, providing the total combined length of ducting is no longer than 5 metres and the maximum length to the first outlet should not exceed 1.5m.
Q: What is the electrical consumption?
A: 1.6amps on 12v
Q: I have an old Carver P4 air heater do you do a replacement?
A: Yes, the HS2000, HS2211or the HS2800.
Q: Can the heater be mounted vertically?
A: The heater must not be mounted vertically on its nose or end or upside down but on one of its sides is not a problem. Remember when mounting the unit you should ensure you can still maintain access to the electronics cover and gas connections
Q: Where can the heater be fitted?
A: Most installations are mounted in a bedbox or locker. External installation is not recommended unless using the appropriate mounting box. However the HS2211 is designed to be fitted externally.
Q: How noisy is the heater?
A: There is very little burner noise from the heater itself. However, there will be some noise from the blown hot air similar to that of a small domestic fan heater.
Q: Can the heaters be used while vehicles are moving?
A: Yes, a vehicle in motion flue terminal is available and the heater should be installed and operated in compliance with the relevant regulatory requirements. Use of the the correct VIM bracket ensure compliance with the vehicle in motion test regime.
Q: What length of exhaust flue pipe can be fitted?
A: Total combined length must not exceed 4 meters and the inlet pipe should be slightly longer than the exhaust to balance the burner.
Q: What is the electrical consumption?
A: 1.6amps on 12v
Q: I want to replace my old Carver Cascade , will I need to cut new holes for the Malaga?
A: No, we can supply an adapter plate with a new Malaga that will make a neat job of the inlet and exhaust termination.
Q: I have an old Belling Malaga water heater that no longer works, what do I do?
A: Two options here, we can either supply you a complete replacement Malaga heater or, if its only your control PCB that’s failed, we can upgrade your existing Belling unit.
Q: What type of pump is needed to work in conjunction with the heater?
A: The Malaga will work with an in line or submersible pump providing the maximum pressure does not exceed 1.5bar or 20 PSI.
Q: Will it work on an electrical mains hook up?
A: The Malaga IIE needs removing and replacing with Malaga 5E
Q: How large is the Malaga water tank?
A: 13.5 litres
Q: Are they suitable for marine use?
A: No, except on vessels used exclusively on Class 1 & 2 Waterways, so inland waterways. The installation must be made where an external vertical or near vertical wall is available.
Q: Where can I mount the heater?
A: Typically in a bedbox or locker with easy access to flue through a side wall.
Q: I have an old Carver P4 air heater do you do a replacement?
A: Yes, the HS2000, HS2211 or the HS2800.
Q: Can the heater be mounted vertically?
A: The heater must not be mounted vertically on its nose or end or upside down but on one of its sides is not a problem. Remember when mounting the unit you should ensure you can still maintain access to the electronics cover and gas connections
Q: Where can the heater be fitted?
A: Most installations are mounted in a bedbox or locker. External installation is not recommended unless using the appropriate mounting box. However the HS2211 is designed to be fitted externally.
Q: How noisy is the heater?
A: There is very little burner noise from the heater itself. However, there will be some noise from the blown hot air similar to that of a small domestic fan heater.
Q: Can the heaters be used while vehicles are moving?
A: Yes, a vehicle in motion flue terminal is available and the heater should be installed and operated in compliance with the relevant regulatory requirements. Use of the the correct VIM bracket ensure compliance with the vehicle in motion test regime.
Q: What length of exhaust flue pipe can be fitted?
A: Total combined length must not exceed 4 meters and the inlet pipe should be slightly longer than the exhaust to balance the burner.
Q: What is the electrical consumption?
A: 1.6amps on 12v
Files
HS2800Feb.pdf
HS2800_Instructions_Issue_4.pdf
Marine_Installation.pdf
Heatsource_A3_brochure.pdf
HS2000_issue_2.pdf
HS2000Feb.pdf
Heatsource_A3_brochure.pdf
HS2211-flyer.pdf
HS2800Feb.pdf
HS2800_Instructions_Issue_4.pdf
Marine_Installation.pdf
Heatsource_A3_brochure.pdf
Malaga_3_instructions_Issue_C.pdf
Malaga_II_Instructions_issue_D.pdf
Malaga_Mk3_leaflet.pdf
Malaga_Mk4_issue_G.pdf
HS2000_issue_2.pdf
HS2000Feb.pdf
Heatsource_A3_brochure.pdf