HS2211 External Gas Air Heater
$1,590.00 CAD
The Weatherproof Propex HS2211 Heater is an automatic thermostatically controlled blown air heating system fuelled by propane/butane gas. Heatsource is designed for a variety of automotive and marine applications as a source of heat totally independent of the engine and most commonly used on exterior mounts.
Description
Electrical Equipment:
Propex Wiring Harness
Propex Thermostat
Exhaust & Intake Equipment:
1” S/S Flexible Exhaust Tube 3’ (2)items
1” Galvanized Exhaust Clamp (2) items
1 ½” S/S Hose Clamp (2)items
Ducting Equipment:
3” PAK Hot Air Duct 1 Meter
Propex 80mmx3” Adapter (2)items
Propex 80mm Non Closable Vent (1) items
75mm Aurora Grill
3” S/S Hose Clamp (8) items
Mounting Equipment:
Vehicle Mount Kit
FAQ
Q: Can the heater be mounted vertically?
A: The heater must not be mounted vertically on its nose or end or upside down but on one of its sides is not a problem. Remember when mounting the unit you should ensure you can still maintain access to the electronics cover and gas connections
Q: Where can the heater be fitted?
A: Most installations are mounted in a bedbox or locker. External installation is not recommended unless using the appropriate mounting box. However the HS2211 is designed to be fitted externally.
Q: How noisy is the heater?
A: There is very little burner noise from the heater itself. However, there will be some noise from the blown hot air similar to that of a small domestic fan heater.
Q: Can the heaters be used while vehicles are moving?
A: Yes, a vehicle in motion flue terminal is available and the heater should be installed and operated in compliance with the relevant regulatory requirements. Use of the the correct VIM bracket ensure compliance with the vehicle in motion test regime.
Q: What length of exhaust flue pipe can be fitted?
A: Total combined length must not exceed 4 meters and the inlet pipe should be slightly longer than the exhaust to balance the burner.
Q: How many outlets can you put on the Heatsource HS2000, HS2000E and HS2211?
A: The maximum recommended is 3, providing the total combined length of ducting is no longer than 5 metres and the maximum length to the first outlet should not exceed 1.5m.
Q: What is the electrical consumption?
A: 1.6amps on 12v
Q: How much do they cost?
A: From as little as £496 for a Heatsource 2000 complete with a single outlet vehicle fitting kit and thermostat.
Technical Specifications
| HS2211 Technical Specifications | |
|---|---|
| Maximum dimensions | Height: 230mm, Width: 157mm, length: 430mm |
| Weight | Under-floor Installation 7.7kg |
| Gas | Butane 28-30mbar – CAT I3+ (28-30/37), Butane/Propane 30mbar – CAT I3B/P (30) |
| Propane | 37mbar – CAT I3p (37) |
| Gas Consumption | (M) 150g/h |
| Classification of Heater | Type: C53 (Fanned) Normal Installation C13 Vehicle In Motion Installation |
| Nominal Heat Input | Gas 2.0Kw |
| Battery Supply | |
| Nominal voltage | 12V d.c. |
| Operating range | 10.0V d.c. min. to 15V d.c. max. |
| Maximum current | d.c. gas operation: 1.7 Amps (0.01Amps on standby) |
| Dry Storage Temperature | -20°C to 70°C |
| Hot Air Duct Diameter | 60mm ID |
| Flue Diameter | 22mm ID |
| Maximum Exhaust Flue Length | 2m |
| Minimum Exhaust Flue Length | 0.75m |
| Maximum Combustion Air Flue Length | 2m |
| Minimum Combustion Air Flue Length | 1.0m |
Resources
Technical Specifications
| HS2211 Technical Specifications | |
|---|---|
| Maximum dimensions | Height: 230mm, Width: 157mm, length: 430mm |
| Weight | Under-floor Installation 7.7kg |
| Gas | Butane 28-30mbar – CAT I3+ (28-30/37), Butane/Propane 30mbar – CAT I3B/P (30) |
| Propane | 37mbar – CAT I3p (37) |
| Gas Consumption | (M) 150g/h |
| Classification of Heater | Type: C53 (Fanned) Normal Installation C13 Vehicle In Motion Installation |
| Nominal Heat Input | Gas 2.0Kw |
| Battery Supply | |
| Nominal voltage | 12V d.c. |
| Operating range | 10.0V d.c. min. to 15V d.c. max. |
| Maximum current | d.c. gas operation: 1.7 Amps (0.01Amps on standby) |
| Dry Storage Temperature | -20°C to 70°C |
| Hot Air Duct Diameter | 60mm ID |
| Flue Diameter | 22mm ID |
| Maximum Exhaust Flue Length | 2m |
| Minimum Exhaust Flue Length | 0.75m |
| Maximum Combustion Air Flue Length | 2m |
| Minimum Combustion Air Flue Length | 1.0m |
FAQ
Q: Can the heater be mounted vertically?
A: The heater must not be mounted vertically on its nose or end or upside down but on one of its sides is not a problem. Remember when mounting the unit you should ensure you can still maintain access to the electronics cover and gas connections
Q: Where can the heater be fitted?
A: Most installations are mounted in a bedbox or locker. External installation is not recommended unless using the appropriate mounting box. However the HS2211 is designed to be fitted externally.
Q: How noisy is the heater?
A: There is very little burner noise from the heater itself. However, there will be some noise from the blown hot air similar to that of a small domestic fan heater.
Q: Can the heaters be used while vehicles are moving?
A: Yes, a vehicle in motion flue terminal is available and the heater should be installed and operated in compliance with the relevant regulatory requirements. Use of the the correct VIM bracket ensure compliance with the vehicle in motion test regime.
Q: What length of exhaust flue pipe can be fitted?
A: Total combined length must not exceed 4 meters and the inlet pipe should be slightly longer than the exhaust to balance the burner.
Q: How many outlets can you put on the Heatsource HS2000, HS2000E and HS2211?
A: The maximum recommended is 3, providing the total combined length of ducting is no longer than 5 metres and the maximum length to the first outlet should not exceed 1.5m.
Q: What is the electrical consumption?
A: 1.6amps on 12v
Q: How much do they cost?
A: From as little as £496 for a Heatsource 2000 complete with a single outlet vehicle fitting kit and thermostat.